Forge & Flame Accentra52i-TC 24" pellet insert

Forge & Flame Accentra52i-TC 24" Pellet Insert

Pellet Insert · Powered by Harman Technology

Forge & Flame Accentra52i-TC 24"

Heritage: Harman

The Accentra52i-TC with the larger 64.5 lb hopper, for fewer trips to the pellet bags.

Heating Capacity1,250–2,500 sq ft
Efficiency76% (higher heating value)
Hopper Size64.5 lb
FuelPellet
ControlsTouch control panel on the insert with a wireless room sensor
FanIncluded

Figures per the manufacturer. Real-world results depend on your home, fuel, and install.

Not every dealer carries every model. We'll show you what's available near you, the local dealers who can help, and a free Project Guide you can take to any dealer.

See the Accentra52i-TC 24" on the manufacturer's site: forgenflame.com/products/harman-accentra-52i-tc-pellet-fireplace-insert ↗

On This Page

  1. Who It's For
  2. What Makes It Special
  3. Possible Downsides
  4. Manuals and Documents
  5. Frequently Asked Questions

Who It's For

Pellet heat is easy until you are filling the hopper every day in January. Refills should be the exception. You need an insert that carries enough fuel to run a long stretch on its own. If you want your fireplace to heat much of the house and you would rather fill it less often, the Forge & Flame Accentra52i-TC 24-inch, powered by Harman technology, is built for that. Choose it and the pellet bags stay in the garage longer.

What Makes It Special

This version holds 64.5 lb of pellets, compared with 47.5 lb in the 20-inch model. Same heat, longer between fills.

Two blowers move the warmth out into the room, and a wireless room sensor lets the insert hold the temperature you set on the touch panel. For service, the insert slides forward on a track. The lit hopper lid shows the fuel level, and the mirrored glass goes dark and clean when the fire is out.

Possible Downsides

If you want strong fireplace heat with the fewest refills, the Forge & Flame Accentra52i-TC 24-inch is the right decision. One fill carries you through the cold stretch, and the room stays steady the whole time.

Choose Matte Black or Majolica Brown, then add a ceramic log, a surround extension or custom surround, a flue rough-in support kit, a service rail kit, or zero-clearance installation kits.

Manuals and Documents

Documents open on the manufacturer's website. Your installer follows the manual for your exact install.

Frequently Asked Questions

How much space can the Forge & Flame Accentra52i-TC 24-inch pellet insert heat?

Expect it to heat about 1,250–2,500 sq ft, enough to carry much of a house from the fireplace. It's rated 76% efficient on the higher heating value scale and is EPA certified at 1.1 g/hr under the 2020 particulate emission standards.

How is the 24-inch Accentra52i-TC different from the 20-inch version?

It holds 64.5 lb of pellets instead of 47.5 lb, so you get the same heat with longer stretches between fills. The tradeoff is size: the standard 24-inch unit needs a 24-inch fireplace opening height, while the 20-inch version fits shorter openings.

Can the Accentra52i-TC go into my existing fireplace?

Yes, it's made for masonry or factory-built wood fireplaces. In masonry, the minimum vent is 4-inch stainless flex pipe running at least 12 inches past a sealed damper plate. Factory-built fireplaces need the manufactured fireplace installation kit, and older or non-HT chimneys need a full-height liner.

Is the Accentra52i-TC approved for mobile homes?

Yes, it's approved for mobile homes when it isn't in a sleeping room. A Forge & Flame outside air kit must be installed, the insert must be grounded to the home's frame with at least 8 AWG copper wire, and only listed Class PL pellet vent can be used.

How do I set the temperature on the Accentra52i-TC?

You set it on the touch control panel, and the wireless room sensor tells the insert the temperature where you want to feel the heat. The Easy Touch screen also handles scheduling, fuel gauges, diagnostics, and cleaning prompts, while the exhaust sensing probe adjusts output to hold your setting.

What happens to the Accentra52i-TC in a power outage?

It needs household power, and when the combustion blower stops, exhaust can seep into the room. The manual recommends a backup in outage-prone areas: the tested TrippLite INTERNET750U UPS for a safe shutdown, or an approved inverter/charger on a 12-volt deep-cycle battery for up to eight hours of operation.

What clearances and hearth protection does the Accentra52i-TC need?

The installation manual calls for 12 inches from the insert body to a sidewall and to a 12-inch-deep mantel, with zero clearance from 3/4-inch trim to the cast surround. Floor protection must extend 6 inches in front of the glass and be at least 16.5 inches deep by 30 inches wide.

What finishes and add-ons are available for the Accentra52i-TC 24-inch?

Choose matte black or Majolica Brown. The small surround is standard, and you can add a surround extension or a custom surround up to 60 by 47 inches, a ceramic log with its bracket, a service rail kit, or zero-clearance kits. A dealer trained on this model has to order and install it.

The Harman Story

Harman was founded by Dane Harman, a welder, who built his first stove in 1978 and started Harman Stove and Welding beside his home in Halifax, Pennsylvania, in 1979. Its pellet stoves grew out of a patented coal stoker, with a bottom-feed burn pot that pushes ash out and a probe that feeds by temperature. Hearth & Home Technologies bought Harman in 2007, and since 2023 its stoves have been sold under the Forge & Flame name, “Powered by Harman Technology.”

Read the full Harman story →

Find a Local Dealer for Your Fireplace Project

Enter your zip or postal code. We'll show you what's available near you, the local dealers who can help, and a free Project Guide & Parts List you can take to any dealer.

Not every dealer carries every model. We'll show you what's available near you, the local dealers who can help, and a free Project Guide you can take to any dealer.

More Harman Pellet Models

All Harman →
Forge & Flame P42i-TC 24" Pellet Fireplace pellet fireplaceP42i-TC 24" Pellet FireplaceForge & Flame · Pellet Fireplace

Heating Capacity: 1,050–2,100 sq ft

Forge & Flame Pathfinder P61 pellet stovePathfinder P61Forge & Flame · Pellet Stove

Heating Capacity: 1,500–3,050 sq ft

Forge & Flame Pathfinder P43 pellet stovePathfinder P43Forge & Flame · Pellet Stove

Heating Capacity: 1,150–2,250 sq ft

Forge & Flame Allure50 pellet stoveAllure50Forge & Flame · Pellet Stove

Heating Capacity: 1,300–2,650 sq ft

Other Forge & Flame Pellet Inserts

All Forge & Flame →
Forge & Flame Trekker Insert pellet insertTrekker InsertForge & Flame · Pellet Insert

Heating Capacity: 1,300–2,550 sq ft

Forge & Flame Santa Fe Insert pellet insertSanta Fe InsertForge & Flame · Pellet Insert

Heating Capacity: 750–1,550 sq ft

Forge & Flame Classic Bay 1200 Insert pellet insertClassic Bay 1200 InsertForge & Flame · Pellet Insert

Heating Capacity: 1,200–2,450 sq ft

Forge & Flame and Harman are trademarks of Hearth & Home Technologies. Find My Fireplace is independent and not affiliated with or endorsed by Forge & Flame or Hearth & Home Technologies. Product details are drawn from the manufacturer's published brochures and manuals; our evaluations are our own.

Product images may be computer renderings; confirm finishes and options before purchase.