Forge & Flame Stardance IFT gas stove

Forge & Flame Stardance IFT Gas Stove

Gas Stove · Crafted with Vermont Castings Finish

Forge & Flame Stardance IFT

Heritage: Vermont Castings

Midsize cast iron gas heat you control from the couch.

Heating Capacity700–1,400 sq ft
FuelNatural gas or propane
ControlsElectronic ignition with battery backup; touchscreen thermostat remote included; app control available
FanIncluded

Figures per the manufacturer. Real-world results depend on your home, fuel, and install.

Not every dealer carries every model. We'll show you what's available near you, the local dealers who can help, and a free Project Guide you can take to any dealer.

See the Stardance IFT on the manufacturer's site: forgenflame.com/products/vermont-castings-stardance-direct-vent-gas-stove ↗

On This Page

  1. Who It's For
  2. What Makes It Special
  3. Possible Downsides
  4. Manuals and Documents
  5. Frequently Asked Questions

Who It's For

Getting up to adjust the stove every hour gets old fast. You want midsize gas heat you can run from your seat. The Forge & Flame Stardance with electronic ignition, crafted with Vermont Castings, is for the main living room where the owner wants classic looks and modern control. A manual stove keeps you on your feet; this one keeps you comfortable.

What Makes It Special

The included touchscreen thermostat remote holds the temperature you set, and the Wi-Fi module adds app control.

Electronic ignition means no pilot flame between fires, and battery backup keeps it working during an outage. A variable-speed blower is built in to spread the heat.

A four-piece split oak log set on a ceramic burner sits behind operable doors, in classic black, majolica brown, bordeaux, or sand.

Possible Downsides

If you want a midsize gas stove you can run without leaving your seat, the Forge & Flame Stardance is the right decision. A tap on the remote, and the living room is warm before the popcorn is ready.

Choose classic black, majolica brown, bordeaux, or sand with a warming shelf, and add a propane conversion kit, vent paint, or the Wi-Fi module.

Manuals and Documents

Documents open on the manufacturer's website. Your installer follows the manual for your exact install.

Frequently Asked Questions

How much space will the Forge & Flame Stardance gas stove heat?

Plan on 700–1,400 sq ft, which suits a main living room. On natural gas it runs from 20,000 to 28,000 BTU per hour, or 21,000 to 25,000 on propane, and the brochure lists 81% steady-state efficiency and 67% AFUE.

Does the Stardance keep working during a power outage?

Yes. Its IntelliFire Touch ignition has a battery backup that runs on four AA batteries, so you can still light the fire when the power is out. On battery power, you lose the fan, lights, and other features that need household current, and the manual says batteries are for emergencies only.

What can the Stardance remote do?

The included IFT-RC400 touchscreen remote turns the stove on and off and adjusts flame height, thermostat mode, the Cold Climate pilot, and the built-in variable-speed fan. For app control, add the separate Wi-Fi module. As a safety feature, the stove shuts itself off after 9 hours without a remote command.

Can I run the Stardance on propane?

Yes, but you'll need the propane conversion kit, because the stove runs only on the gas shown on its rating plate unless a certified kit is used. Without derating, it's certified up to 2,000 feet on natural gas and 4,500 feet on propane.

How is the Stardance vented?

It's a direct-vent stove that vents from the top, through an outside wall or up through the roof, using outside air for combustion. Horizontal setups need at least 24 inches of vertical rise before the first elbow and can run up to 20 feet out, and vertical setups must end 8 to 40 feet above the flue collar.

How close to the wall can the Stardance go, and can it sit in an alcove?

It needs just 4 inches to the back wall, measured from the rear skirt, and 4 inches at the sides. It's approved for a combustible alcove up to 48 inches deep, at least 72 inches high when the minimum vent kit is used. On carpet, set it on a metal or wood panel the full width and depth of the stove.

Can the Stardance go in a bedroom or a mobile home?

Yes to both, within limits. The manual approves it for bedroom installations in the US and Canada, and for permanently located manufactured homes (US only) or mobile homes where local codes don't prohibit it. It also calls for an inspection before use and at least once a year by a qualified service agency.

What finishes does the Stardance come in?

Choose classic black, majolica brown, bordeaux enamel, or sand, and pick a warming shelf, which is a required selection; shelves come in classic black, majolica brown, and bordeaux. Every finish has operable doors and a four-piece split oak log set on a ceramic burner, and gas vent paint is available in majolica brown and bordeaux.

The Vermont Castings Story

Vermont Castings was founded in 1975 by Duncan Syme, the designer, and his brother-in-law Murray Howell, the business partner, in Randolph, Vermont. Their first stove, the cast-iron Defiant, went on sale in 1976. The company has changed hands several times since 1990, and Hearth & Home Technologies has owned it since 2014. Since 2023, Vermont Castings stoves have been sold under the Forge & Flame name, still cast in Randolph.

Read the full Vermont Castings story →

Find a Local Dealer for Your Fireplace Project

Enter your zip or postal code. We'll show you what's available near you, the local dealers who can help, and a free Project Guide & Parts List you can take to any dealer.

Not every dealer carries every model. We'll show you what's available near you, the local dealers who can help, and a free Project Guide you can take to any dealer.

More Vermont Castings Gas Models

All Vermont Castings →
Forge & Flame Intrepid DV gas stoveIntrepid DVForge & Flame · Gas Stove

Heating Capacity: 450–950 sq ft

Forge & Flame Stardance DV gas stoveStardance DVForge & Flame · Gas Stove

Heating Capacity: 700–1,400 sq ft

Forge & Flame Radiance IFT gas stoveRadiance IFTForge & Flame · Gas Stove

Heating Capacity: 950–1,900 sq ft

Forge & Flame Radiance DV gas stoveRadiance DVForge & Flame · Gas Stove

Heating Capacity: 950–1,900 sq ft

Forge & Flame and Vermont Castings are trademarks of Hearth & Home Technologies. Find My Fireplace is independent and not affiliated with or endorsed by Forge & Flame or Hearth & Home Technologies. Product details are drawn from the manufacturer's published brochures and manuals; our evaluations are our own.

Product images may be computer renderings; confirm finishes and options before purchase.