Heat That Stays On When Storms Knock Out the Power.

Most gas fireplace installations in Moore run between $3,500 and $8,500, depending on the unit, the venting path, and whether new gas line work is needed. A direct-vent insert dropped into an existing masonry fireplace—common in Moore's 1970s–2000s ranch and split-level homes—tends to land on the lower end, since it uses the existing chimney chase. A new built-in gas fireplace in a remodel, requiring fresh framing and a run to the gas line, sits higher. A local dealer will give you a firm number after seeing your fireplace or wall cavity in person.

Yes, and it's one of the most common requests from Moore homeowners. Many houses in Cleveland County were built with a traditional wood-burning masonry fireplace that rarely gets used—Moore's mild winters and lack of a strong firewood-cutting culture mean those fireboxes often just sit cold most of the year. A gas insert converts that fireplace into a real heat source, using a stainless liner run through the existing chimney. Expect $4,000 to $8,000 depending on the insert and whether a new gas line needs to be run to the hearth.

Either works, and it depends on where you are in Moore. Homes in established parts of the city typically already have natural gas service for the furnace and water heater, so adding a fireplace is usually a simple tie-in. For newer subdivisions on the edges of Cleveland County or homes without gas service, propane is a common alternative, supplied from a tank on the property. Most gas fireplace models can be set up for either fuel—your installer sets the correct orifice and regulator for whichever you have.

Moore residents know power outages come with the territory—ice storms and the occasional tornado can take out the grid for hours or days. Most gas fireplaces with IPI (intermittent pilot ignition) include a battery backup that kicks in automatically and lets you light the unit on demand even with no electricity. Valor units go a step further: the pilot's thermocouple generates the small amount of electricity the unit needs, so there's no battery to check or replace. If storm resilience matters to you, ask your local dealer specifically about the ignition system on any model you're considering.

A gas fireplace is a fully built-in unit framed into a wall—the right call for new construction or a remodel with no existing fireplace. A gas insert slides into an existing masonry firebox, which fits a lot of Moore's older housing stock, and uses the chimney as its vent path. A gas stove is a freestanding cast-iron or steel unit that sits on the floor and can go almost anywhere with proper clearances, useful for a garage conversion or a room without an existing chimney. Most Moore homeowners with an unused wood fireplace end up choosing an insert.

Yes—installing or converting a gas fireplace in Moore requires a building permit through the City of Moore's building codes division, plus a gas line permit if any new gas piping is involved. The gas line portion has to be handled by a licensed gas-fitter. Most established hearth dealers coordinate all of this as part of the installation, so you're not left managing separate inspections for the framing, venting, and gas work yourself.

Oklahoma permits vent-free (ventless) gas fireplaces, and they show up in some Moore homes, particularly as secondary units or in rooms where running venting isn't practical. They burn fuel directly into the room air, so sizing rules and an oxygen depletion sensor are required for safety. Direct-vent units, which pull combustion air from outside and exhaust it back out through a sealed pipe, are still the more common recommendation for main living areas—they don't introduce moisture or combustion byproducts into the house. A local dealer can walk you through both options for your specific room.

Plan on an annual inspection, ideally before the first cold front of the season. A technician checks the burner, pilot assembly, venting, and gas connections, and cleans the glass and interior—a much quicker visit than a wood chimney sweep, but important because Moore's fireplaces often sit unused for stretches between cold snaps, which is exactly when dust, spiders, or debris can build up in the burner or vent. Most local service providers charge in the $150–$250 range for a standard inspection.

Gas delivers real heat output—enough to noticeably warm a room during a January cold snap—and, with the right ignition system, keeps working through a power outage. Electric fireplaces plug into a standard outlet, need no venting or gas line, and cost far less to install, but they rely on the grid and OG&E or Oklahoma Electric Coop rates (currently around 11.8–12.3 cents per kWh) rather than delivering the same heat density as gas. For a supplemental heat source in a family room during Moore's coldest weeks, gas is usually the better fit; for ambiance in a bedroom, basement, or rental property, electric is often plenty.

If it was installed more than 15 years ago, probably. Older gas fireplaces keep a standing pilot light burning all the time, and that little flame can cost a couple hundred dollars a year. Newer models use pilot-on-demand ignition—the pilot lights only when you use the fireplace and goes out when you turn it off.

Yes—with an asterisk. Fireplaces are hot and TVs don't like heat. Either put a mantel between them to deflect rising warmth, or choose a fireplace with heat-management technology that creates a cool zone on the wall above—the wall stays around 125 degrees, barely warm, while the room still gets full heat. If you like clean lines and don't want a mantel, heat management is the answer.

For an average home—covering the fireplace, the vent pipe, and basic installation—a budget between $3,900 and $5,500 gives you a lot of options across wood, gas, and pellet. By the time you add finish work, gas line, and electrical, the average complete installation lands between $5,000 and $12,000 all-in. In a remodel or new build, a good rule is to put about 2.5% of the total project cost toward the fireplace.

It's a visit where a hearth professional measures your space, confirms the model you picked actually works in your home, and walks the specs—framing, gas line, venting, finish work—before anything is ordered. Some details you just can't know until you see the house. Never make a down payment without one; it's the single most-skipped step that burns buyers.