Warm, Clean Heat for Englewood Homes.
From Cliffside colonials to newer builds off Route 4, gas delivers instant, low-maintenance heat without the wood storage or chimney upkeep. Find the right unit and connect with a trusted local dealer.
Every Project Starts From One of These Five Situations
Gas fits how Englewood actually heats.
Englewood sits low—43 feet above sea level, just across the George Washington Bridge from Manhattan—and its winters are moderate by Northeast standards: an average winter low around 26°F and a winter heating load that's well short of what a town like Burlington, VT deals with, but still cold enough that supplemental heat matters from November through March. The city's housing stock is a mix of 1920s-to-1950s colonials and Tudors in neighborhoods like Lincoln Park and Liberty Road, many with existing masonry fireplaces, alongside newer townhomes and condo buildings along the Route 4 corridor that were never built with a chimney at all.
Public Service Electric & Gas Co. (PSE&G)—as the name suggests—runs both the electric grid and the natural gas mains through nearly all of Englewood, so tapping into gas service is usually a matter of running a line to the appliance rather than extending infrastructure from the street. That's a big reason wood-burning is essentially absent here: dense lots, local ordinances, insurance underwriting, and the simple fact that a gas line is already at the curb all push homeowners toward gas or electric instead. A gas insert into an existing masonry fireplace, a built-in unit in a newer great room, or a direct-vent stove in a finished basement all give you real, instant heat without the wood handling, ash cleanup, or chimney fire risk that comes with burning cordwood in a tight residential setting.
Three steps. No salesperson until you're ready.
Tell us about your project
Your zip code, your situation, and the fuel you're leaning toward—or let the answers point you to one.
See what's actually available
The brands dealers within 100 miles genuinely carry—real options, never a catalog mirage.
Get your dealer & Project Guide
A trusted local dealer, plus the free Project Guide & Parts List that names every component of the job.
Frequently Asked Questions
How much does a gas fireplace installation cost in Englewood?
Most Englewood installations run between roughly $4,000 and $10,000, with the spread driven mainly by venting and gas line work rather than the fireplace itself. Because PSE&G gas mains already run through nearly every Englewood block, tapping an existing line for a fireplace is usually straightforward and keeps costs toward the lower end. Jobs that involve a longer gas line run, new framing for a built-in unit in a renovated room, or venting through a masonry chimney that needs a liner tend to land in the middle to upper end of that range. A local dealer will give you a firm number after walking your specific setup.
Can I convert my existing wood fireplace to gas in my Englewood colonial?
Yes—it's one of the most common projects in Englewood's older housing stock. Homes in neighborhoods like Lincoln Park and Cliffside Park border often have a working masonry fireplace that hasn't seen a real wood fire in years, partly because burning wood on a tight residential lot raises insurance and smoke concerns neighbors notice quickly. A gas insert uses your existing chimney with a stainless liner run down to the firebox, typically running $4,000 to $8,500 depending on flue length and whether new gas line work is needed. The result keeps the original fireplace opening and mantel while giving you real heat at the flip of a switch.
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
invalid
Is my gas fireplace wasting gas?
If it was installed more than 15 years ago, probably. Older gas fireplaces keep a standing pilot light burning all the time, and that little flame can cost a couple hundred dollars a year. Newer models use pilot-on-demand ignition—the pilot lights only when you use the fireplace and goes out when you turn it off.
Why is a fireplace insert so efficient?
An insert does two things: it seals the chimney completely, so you stop losing air you already paid to heat, and it radiates warmth into the room through the firebox and glass. Most add a heat-exchange fan that pulls cool room air underneath, wraps it around the hot firebox, and pushes it back out warm. Your home is more efficient before you've even lit the first fire.
What is an in-home preview and do I need one?
It's a visit where a hearth professional measures your space, confirms the model you picked actually works in your home, and walks the specs—framing, gas line, venting, finish work—before anything is ordered. Some details you just can't know until you see the house. Never make a down payment without one; it's the single most-skipped step that burns buyers.
Can I install a fireplace myself?
If you're putting a fire in your house on purpose, it's best to work with an expert. Unless you're genuinely experienced in framing, gas line, vent pipe, and the national code on clearances to combustibles, have a professional do it—and ideally the same company that sells you the fireplace, so warranty, service, and liability all live under one roof.
Nearby Dealers
Hearth shops serving Englewood and the surrounding area. Every listing shows whether it is a WhyFire partner, a dealer we have verified as authorized for the brands we recommend, or a local business carrying hearth products. No manufacturer pays for placement. How we verify dealers →